AVN-DIO10-12G Dante® to 12G/6G/3G/HD/SD-SDI Embedder/De-Embedder
An upgrade to the extremely popular AVN-DIO10, the new AVN-DIO10-12G now adds support for the full range of SDI standards from SD-SDI through to 12G-SDI. The AVN-DIO10-12G can be used for simultaneous embedding and de-embedding of up to 64 channels. This simple plug and play audio/video interface provides a convenient and elegant method of connecting legacy 12G/6G/3G/HD/SD-SDI equipment to the Dante® AoIP audio network.
The AVN-DIO10-12G can be used for simultaneous embedding and de-embedding for up to 64 channels. This simple plug and play audio/video interface provides a convenient and elegant method of connecting legacy 12G/6G/3G/HD/SD-SDI equipment to the Dante® AoIP audio network.
The AVN-DIO10-12G takes an SDI feed, de-embeds up to 64 audio channels and places them on channels 1-64 on the Dante network, mapped using Dante Controller. It simultaneously takes the 64 input channels mapped to the device on Dante Controller and re-embeds them onto the SDI output.
The unit also contains an integrated SDI generator to allow embedding onto the SDI output without the need of an SDI input. This is fully configurable through the web UI.
Other controls provided through the web UI allow embedding of Dante channels onto the SDI output per channel pair and there are two modes of operation: Insert Mode enabled allows embedding to overwrite existing SDI audio selectively per channel pair. Insert Mode disabled clears any incoming audio channels on the SDI output and then allows selective embedding onto the SDI output per channel pair.
Test Tone mode allows 1kHz, 2kHz, 3kHz and 4kHz signals to be output on channels 1 to 4 respectively, for any group where embedding is enabled. This is so that downstream SDI audio outputs can be tested without the need of Dante sources.
It’s powered by Power over Ethernet (PoE), using Neutrik® EtherCON connectors, with primary and secondary ports for power and data redundancy. The AVN-DIO10-12G uses the latest Audinate Dante® chipsets so is AES67 and Dante Domain Manager® compliant. There are front panel LEDs to indicate network clock status, SDI lock status, AoIP Primary and AoIP Secondary link status, PoE Primary power and PoE Secondary power active.
A web interface is available for firmware updates, control, status information and network settings.
Up to 3 of the AVN-DIO10-12G units can be rackmounted in the 1U AVN-DIORK.
- 1 x 12G/6G/3G/HD/SD-SDI input.
- 1 x reclocked 12G/6G/3G/HD/SD-SDI output.
- Dual redundant Primary and Secondary Dante network ports using Neutrik EtherCon® Ethernet connectors.
- Powered via PoE (Power over Ethernet) with PoE dual redundancy.
- Fully Dante compliant device.
- AES67 compatible.
- Dante Domain Manager compliant.
- Web interface for configuration.
- Clock, SDI Lock, PoE and Sync LEDs.
- Overwrite or insert into existing SDI audio groups.
- Test tones available on embedded outputs.
- SDI audio sample rate support at 48kHz.
- All available Dante sample rates supported.
- Sample rate conversion of audio between Dante and SDI.
- Dante clock domain can be optionally synchronised from the SDI clock.
- 3 x units rackmount in the AVN-DIORK.
Technical Specification For AVN-DIO10-12G |
|
Parameter SDI Input |
|
| Input Impedance: | 75Ω Unbalanced |
| SDI Supported Standards: |
270Mbps SMPTE-259M-C (SD) |
| Supported Video Formats: | 525/59.94 (SMPTE-125M) 625/50 (ITU-R BT.656) 720p/23.98, 24, 25, 29.97, 30, 50, 59.94, 60 (SMPTE-296M) 1035i/59.94, 60 (SMPTE-260M) 1080i/50, 59.94, 60 (SMPTE-274M) 1080p/23.98, 24, 25, 50, 59.94, 60 (SMPTE-274M) 1080pSF/23.98, 24, 25, 29.97, 30 (RP-211) 1080i/50 (SMPTE-295M) 1080p/50 (SMPTE-295M) 2160p/23.98, 24, 25, 29.97, 30, 50, 59.94, 60 (SMPTE-2036) |
| Embedded Audio: | 48kHz, synchronous SMPTE-272M-ABC SMPTE-299M SMPTE-299-2 (De-embedding only) |
| Supported Image Mapping: | SMPTE-425M-AB |
Parameter SDI Output |
|
| Output Impedance: | 75Ω Unbalanced |
| Alignment Jitter: | <0.2UI |
| Output Level: | 800mV ±10% |
| Return Loss: | TBC |
| SDI Supported Standards: | Loop-through - Output follows input Generator – See above standards |
| Supported Video Formats: | Loop-through - Output follows input Generator – See above formats |
| Embedded Audio: | 48kHz, synchronous SMPTE-272M-C SMPTE-299M |
Network and AoIP |
|
| AoIP Standard: | Dante |
| Channels: | 44.1/48kHz - 64 receive, 64 transmit 88.2/96kHz – 32 receive, 32 transmit 176.4/192kHz – 16 receive, 16 transmit |
| Flows: | 32 receive, 32 transmit |
| Sample Rates: | 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz |
| Encoding: | PCM 16, PCM 24, PCM 32 |
| AES67 Support | Yes |
| Connectivity: | 2 x etherCON (RJ45 compatible) |
| Speed: | 1Gbps or 100Mbps |
| Network Modes: | Switched or redundant |
| Dante Domain Manager Ready: | Yes |
| Clock Source: | Internal (PTP Leader), Network PTP Leader or from SDI input (Sync to External) |
PoE Power |
|
| Standard | 802.3af |
| Redundancy | Yes |
| Class | 0 |
| PD Power Range | 0.44 W to 12.94 W |
| Typical PSE Power Usage | 6 W |
| Max PSE Usage | 15.4 W |
Equipment Type |
|
| AVN-DIO10-12G: | Dante to 12G/6G/3G/HD/SD-SDI Embedder/De-Embedder |
Physical Specification |
|
| Dimensions (Raw): | 14.0cm (W) x 13.6cm (D) x 4.2cm (H) 5.5” (W) x 5.4” (D) x 1.7” (H) |
| Dimensions (Boxed): | 17.8cm (W) x 17cm (D) x 5.6cm (H) 7.0" (W) x 6.7" (D) x 2.2" (H) |
| Weight: | Nett: 0.36kg Gross: 0.55kg Nett: 0.79lbs Gross: 1.21lbs |
Accessories |
|
| AVN-DIOBT AVN-DIOMT AVN-DIORK |
AVN-DIO Large Unit Belt Clip Kit AVN-DIO Large Unit Underdesk Mount AVN-DIO 1U 19" Rack Kit (5 x Small DIO or 3 x Large DIO) |
