Sale
RigExpert AA-230 ZOOM antenna analyzer designed for measuring SWR 0,1-230 MHz w/Bluetooth

RigExpert AA-230 ZOOM antenna analyzer designed for measuring SWR 0,1-230 MHz w/Bluetooth

a powerful antenna analyzer desig The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 230 MHz ned for testing, checking, tuning or repairing antennas and antenna feedlines

Model/Product no.: RE-AA-230-ZOOM-BT
Stock status: In Stock! Shipping within 1-3 working days
Piece

RigExpert AA-230 ZOOM with Bluetooth

The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 230 MHz.

A built-in ZOOM capability makes graphical measurements especially effective.

An integrated Time Domain Reflectometer mode can be used to locate a fault within the feedline system.

 

The following tasks are easily accomplished by using this analyzer:

  • Rapid check-out of an antenna
  • Tuning an antenna to resonance
  • Comparing characteristics of an antenna before and after specific event (rain, hurricane, etc.)
  • Making coaxial stubs or measuring their parameters
  • Cable testing and fault location, measuring cable loss and characteristic impedance
  • Measuring capacitance or inductance of reactive loads

 

RigExpert AA-230 ZOOM – Specifications

Frequency range: 0.1 to 230 MHz

Frequency entry: 1 kHz resolution

Measurement for 25, 50, 75 and 100-Ohm systems

SWR measurement range: 1 to 100 in numerical modes,
1 to 10 in chart modes

SWR display: numerical or analog indicator

R and X range: 0…10000, -10000…10000 in numerical modes,
0…1000, -1000…1000 in chart modes

Display modes:
–    SWR at single or multiple frequencies
–    SWR, return loss, R, X, Z, L, C at single frequency
–    SWR chart, 20 to 500 points
–    R, X chart, 20 to 500 points
–    Smith chart, 20 to 500 points
–    Return loss chart, 20 to 500 points
–    TDR (Time Domain Reflectometer) chart
–    Cable tools (loss and characteristic impedance)

Optional open-short-load calibration.

Non Volatile memory:
– 100 slots to save measurement results

RF output:
–    Connector type: N
–    Output signal shape: square
–    Output power: -10 dBm (at 50 Ohm load)

Power:
–    Four 1.5V alkaline batteries, type AAA
–    Four 1.2V Ni-MH batteries, type AAA *
–    Max. 4 hours of continuous measurement, max. 2 days in stand-by mode when fully charged batteries are used
–    When the analyzer is connected to a PC or a DC adapter with USB socket, it takes power from these sources

Interface:
–    290×220 color TFT display
–    6×3 keys on the water-proof keypad
–    Multilingual menus and help screens
–    USB connection to a personal computer

Dimensions: 82 x 182 x 32 mm (3.2 x 7.2 x 1.3 in)

Operating temperature: 0…40 °C (32…104 °F)

Weight: 236 g (8.32 oz)

Warranty: 2 years

GTIN-13: 4820185420082

RigExpert AA-230 ZOOM is made in Ukraine.

Specifications are subject to change without notice.

* Batteries are not included with the analyzer.

 

RigExpert AA-230 ZOOM – How it works?

Structure diagram

The structure diagram of RigExpert AA-230 ZOOM is located below:

The “brain” of the analyzer is STM 32-bit RISC microcontroller. It controls a AD9958 DDS chip running at 500 MHz and generating two sinusoidal signals. Both signals are low-pass filtered and then put through pulse shapers, producing two square signals with LVDS levels. Resistive brigde was chosen to measure parameters of a load because of its simplicity and good frequency response. The switch commutates two outputs of the bridge. After the switch, the signal is mixed with the second channel output to produce audio frequency of 1.5 kHz.This signal is then filtered and fed through the 16-bit ADC to the microcontroller. The 290×220 color TFT display and the 6×3 keys keypad are connected directly to the CPU. The analyzer is equipped with 4 Mbytes of external Flash memory to store measurement results. The USB interface chip allows connecting the analyzer to the PC.

Close look at the bridge

This is a diagram of the resistive bridge and its connection to the mixer:

The switch which is controlled by the CPU feeds the signal from the certain side of the bridge to the mixer chip. When the load is totally active and its resistance is 50 Ω, the bridge is balanced and the switch outputs the same signal in both positions. This eliminates the need of calibration of the analyzer, also giving very good precision near SWR=1.

 

Inside the box

RigExpert AA-230 ZOOM – In the package

 
  • RigExpert AA-230 ZOOM
  • N Male SO-239 Female adaptor
  • USB cable
  • Soft case
  • User’s manual
  • Software manual
  • Alkaline batteries
dsc08331

 

RigExpert AA-230 ZOOM – Specifications

Frequency range: 0.1 to 230 MHz

Frequency entry: 1 kHz resolution

Measurement for 25, 50, 75 and 100-Ohm systems

SWR measurement range: 1 to 100 in numerical modes,
1 to 10 in chart modes

SWR display: numerical or analog indicator

R and X range: 0…10000, -10000…10000 in numerical modes,
0…1000, -1000…1000 in chart modes

Display modes:
–    SWR at single or multiple frequencies
–    SWR, return loss, R, X, Z, L, C at single frequency
–    SWR chart, 20 to 500 points
–    R, X chart, 20 to 500 points
–    Smith chart, 20 to 500 points
–    Return loss chart, 20 to 500 points
–    TDR (Time Domain Reflectometer) chart
–    Cable tools (loss and characteristic impedance)

Optional open-short-load calibration.

Non Volatile memory:
– 100 slots to save measurement results

RF output:
–    Connector type: N
–    Output signal shape: square
–    Output power: -10 dBm (at 50 Ohm load)

Power:
–    Four 1.5V alkaline batteries, type AAA
–    Max. 4 hours of continuous measurement, max. 2 days in stand-by mode when fully charged batteries are used
–    When the analyzer is connected to a PC or a DC adapter with USB socket, it takes power from these sources

Interface:
–    290×220 color TFT display
–    6×3 keys on the water-proof keypad
–    Multilingual menus and help screens
–    USB connection to a personal computer

Bluetooth specs.:
Bluetooth Specification v.4.0 (BLE). Compatible with Android OS ver. 6.0 and higher. Analyzer AA-230 Zoom does not work through Bluetooth connection together with OS Windows and AntScope2.

Dimensions: 82 x 182 x 32 mm (3.2 x 7.2 x 1.3 in)

Operating temperature: 0…40 °C (32…104 °F)

Weight: 236 g (8.32 oz)

Warranty: 2 years

GTIN-13: 4820185420082

RigExpert AA-230 ZOOM is made in Ukraine.

Specifications are subject to change without notice.

 

Product's tags

There are no tags registered.

Mine tags

Customers who bought this product also bought